VAŽNO! Ovdje pročitajte kako se registrirati na forum. Bez registracije, nećete biti u mogućnosti pisati na forumu.

Croduino Basic2 upload problem

Pitanja vezana uz Croduino pločice: Basic serija, NOVA/miniNOVA serija, STM32, Damba itd.
Zaključano
matekardos5#6719
Novak
Novak
Postovi: 3
Pridružen/a: sri ruj 09, 2020 3:56 pm

Croduino Basic2 upload problem

Post Postao/la matekardos5#6719 » sri ruj 09, 2020 4:10 pm

Pozdrav, stigao mi je Basic2 danas i ne uspijevam pokrenuti Blink. Javlja se sljedeća greška:

Kod: Označite sve

Arduino: 1.8.12 (Windows 7), Board: "Arduino Nano, ATmega328P (Old Bootloader)"

Sketch uses 924 bytes (3%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x0b
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
Avatar
david.zovko#3842
e-radionica.com team
e-radionica.com team
Postovi: 436
Pridružen/a: ned tra 15, 2018 2:59 pm
Lokacija: Osijek, Croatia
Kontakt:

Re: Croduino Basic2 upload problem

Post Postao/la david.zovko#3842 » čet ruj 10, 2020 9:03 am

Pozdrav, jeste li instalirali CP2102 drivere? https://e-radionica.com/hr/blog/2015/10 ... 2-driveri/

Možete nam poslati screenshot svoj Tools izbornika iz Arduino IDE?
matekardos5#6719
Novak
Novak
Postovi: 3
Pridružen/a: sri ruj 09, 2020 3:56 pm

Re: Croduino Basic2 upload problem

Post Postao/la matekardos5#6719 » čet ruj 10, 2020 10:02 am

Prilažem screenshot:
slika
Drivere sam instalirao u skladu s uputstvima na vašoj stranici.
Screenshot device managera:
slika
matekardos5#6719
Novak
Novak
Postovi: 3
Pridružen/a: sri ruj 09, 2020 3:56 pm

Re: Croduino Basic2 upload problem

Post Postao/la matekardos5#6719 » čet ruj 10, 2020 10:04 am

Sad vidim u čemu je problem. Izabrao sam krivi port. Nakon što sam izabrao port11 sve radi bez problema. Hvala. Lp
Avatar
david.zovko#3842
e-radionica.com team
e-radionica.com team
Postovi: 436
Pridružen/a: ned tra 15, 2018 2:59 pm
Lokacija: Osijek, Croatia
Kontakt:

Re: Croduino Basic2 upload problem

Post Postao/la david.zovko#3842 » uto ruj 15, 2020 1:55 pm

Tako je! :)
Zaključano