Stranica: 1/1.

Croduino Basic2 upload problem

Postano: sri ruj 09, 2020 4:10 pm
Postao/la matekardos5#4766
Pozdrav, stigao mi je Basic2 danas i ne uspijevam pokrenuti Blink. Javlja se sljedeća greška:

Kod: Označite sve

Arduino: 1.8.12 (Windows 7), Board: "Arduino Nano, ATmega328P (Old Bootloader)"

Sketch uses 924 bytes (3%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x0b
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x0b
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

Re: Croduino Basic2 upload problem

Postano: čet ruj 10, 2020 9:03 am
Postao/la david.zovko#4636
Pozdrav, jeste li instalirali CP2102 drivere? https://e-radionica.com/hr/blog/2015/10 ... 2-driveri/

Možete nam poslati screenshot svoj Tools izbornika iz Arduino IDE?

Re: Croduino Basic2 upload problem

Postano: čet ruj 10, 2020 10:02 am
Postao/la matekardos5#4766
Prilažem screenshot:
slika
Drivere sam instalirao u skladu s uputstvima na vašoj stranici.
Screenshot device managera:
slika

Re: Croduino Basic2 upload problem

Postano: čet ruj 10, 2020 10:04 am
Postao/la matekardos5#4766
Sad vidim u čemu je problem. Izabrao sam krivi port. Nakon što sam izabrao port11 sve radi bez problema. Hvala. Lp

Re: Croduino Basic2 upload problem

Postano: uto ruj 15, 2020 1:55 pm
Postao/la david.zovko#4636
Tako je! :)